What size wire do I need for a 70 amp sub panel?
There is a mininum wire size which is required based on the circuit breaker rating. That size is #4 copper or #2 aluminum. You get this number by using a quality voltage drop calculator by specifying the breaker amperage and a wire length of 1 foot. via
What size wire do I need for a 100 amp sub panel 100 feet away?
This is typically a three-wire cable with three insulated conductors plus a bare copper ground wire. The cable must have a wire gauge sufficient to the amperage of the subpanel—a 100-amp subpanel requires #4 copper wires or, more commonly, #2 aluminum wires, for example. via
What size wire is needed for a 100 amp sub panel?
When it comes to the lines connecting master and secondary panels, where the line will carry as much as a full 100 amps, use a 2-gauge non-metallic sheathed electrical cable. The cable must contain one or two hot wires depending on your needs, one neutral wire, and one ground wire. Each wire should be 2-gauge in size. via
What size wire do I need for 60 amp subpanel?
While it's common to use a 6-gauge wire for 60-amp breakers in practice, it's best to use a 4-gauge wire if you're installing a 60-amp subpanel. via
Will 1 0 aluminum wire fit in a 100 amp breaker?
No, Al #1/0 is good for a maximum of 125A in a dwelling service; possibly 100A if the distance is longer than 100' or so. A 200A service requires a minimum of #4/0 aluminum or #2/0 copper; upsized accordingly if there is a long distance involved. via
Can 8 gauge wire handle 50 amps?
8 AWG may carry a maximum of 70 Amps in free air, or 50 Amps as part of a 3 conductor cable. via
Can a 60 amp breaker feed a 100 amp sub panel?
You can feed a 100 Amp panel with a 60 Amp breaker. Keep in mind that the sub panel needs to be rated above the breaker size. via
Can you run a 100 amp sub panel off a 200 amp main panel?
Of course you can, you can add the 100 amp breaker to your 200 amp as long as it isn't overloaded, to start adding the subpanel you must first calculate how many yards it will be from the main panel to the subpanel, there is a formula that calculates how much friction will be on the wire at the connecting distance, via
Can you run a 100 amp sub panel off a 100 amp main panel?
To the best of my understanding, there is no code issue running a 100A subpanel off a 100A main panel, so long as the wire size is correct, and the installation is correct. For a subpanel, you need four wire service (two hots, a neutral, and an equipment ground). via
Is a ground rod required for a sub panel?
Yes, any sub panel outside of the main building requires it's own ground rod and a ground wire back to the main building. And yes, a sub panel in the same building as the main does not need a ground rod - only the ground wire. via
Can I put a 50 amp breaker in a 100 amp panel?
There is no problem using a sub panel that can take more current than you will ever feed it. Points to note: The cable to your hot tub will be rated for 50A (not 100A); therefore you must not upgrade the breaker in your main panel to 100A. via
What size breaker do I need for a sub panel?
Based on your question, since you will be having a subpanel, you want the breaker feeding the subpanel to be sized for the subpanel or slightly smaller. So if you purchase and install a 200A subpanel, then the breaker should be 200A. If you use a 125A subpanel, then use a 125A breaker. via
What wire size do I need to go 100 feet for a 60 amp service to a workshop?
If the circuit is 100 amp or less you have to size the conductors based on the 60-degree celsius column unless the breaker and the equipment terminations are rated for 75 or 90 degrees. You have to use a #4 conductor to feed a 60 amp circuit. via
What size wire should I use for a 50 amp sub panel?
Base Conductor Size
So in your case, if you want to install a 50 ampere panel, you'll need at least 8 AWG copper conductors. If you want a 60 ampere panel, you'll need 6 AWG copper conductors. via
What size wire should I use for a 50 amp breaker?
50 AMP Wire Size
For a maximum of 50 amps, you'll need a wire gauge of 6. Fifty amp breakers are most often used to power many different appliances. However, a kitchen oven can alone require 50 amps. Many electric dryers also require a 50 amp breaker. via